Hot Oil Pumps for Asphalt Plants
Keep your hot oil moving.
Dean RA hot oil pumps and repair kits for asphalt plants, matched to your nameplate.
When the hot oil pump goes down, the heater goes down with it. This page is for the crew that keeps it running.
RA pumps and repair kits
What an asphalt plant hot oil pump does
The RA is an air-cooled hot oil pump built for heat-transfer oil, so it needs no cooling water.
- Built for hot oil service up to 650°F.
- The RA3146, RA3186 and RA3246 are rated to 350 psig.
- The RA2096 is rated to 100 psig at 650°F.
Dean RA thermal fluid pump: where it fits
The RA3146 and RA3186 have a centerline-mounted casing, which Dean says minimizes thermal growth without disturbing alignment. The RA2096 is foot-mounted. See the Dean RA3146 thermal fluid pump.

Signs your hot oil pump needs a rebuild
- Oil coming out of the barrier overflow pipe after a few hours at temperature. Dean says this signals the mechanical seal is about to fail. A little barrier oil at first heat-up is normal.
- Overheating, vibration or other abnormal running.
- At teardown, a shaft scored under the radial bearing or worn at the lip seal.
Plan your rebuild before startup
If you shut down for winter, rebuild before startup and order kits early. Keeping a spare pump lets you swap it in and rebuild offline.
The RA3146 repair kit
It comes as a pre-assembled shaft kit with the thrust bearings already greased. It doesn't include the impeller, casing, bearing housing, end cover or fan.
What's in the RA3146 8.5" kit 6138148
Match your pump by nameplate
Send us the model, size and serial number from the nameplate. The serial number is also stamped on the suction flange or the top edge of the bearing housing front flange.
The size sets the kit, 8.5" or 10" casing. Both sizes have the same flanges, so the flanges won't tell you which one you have. The impeller trim doesn't change the kit.
Upload a nameplate photo on the quote form and we'll match it.
Replacing a SIHI or other hot oil pump?
Dean RA and SIHI are both horizontal, back pull-out, single-stage hot oil pumps with ductile-iron casings, carbon radial bearings and no cooling water. The published ratings differ.
| Spec | Dean RA | SIHI ZTN |
|---|---|---|
| Max working pressure | Dean advantage: 350 psig, flat to 650°F (RA3146, RA3186, RA3246). RA2096: 100 psig at 650°F. | PN 16: 232 psi (0–120°C), 189 psi (120–300°C), 145 psi (300–350°C) |
| Flanges | Dean advantage: ASME Class 300 (RA2096: Class 150) | EN 1092-2 PN 16 (ANSI 150 drilling available) |
| Shaft seal | Dean advantage: Single mechanical seal, silicon carbide against carbon | Mechanical seal or lip seals, uncooled |
| Max temperature | Up to 650°F | Up to 662°F (350°C) |
| Casing | Ductile iron, ASTM A395 | Ductile iron, ASTM A395 equivalent |
| Bearing housing | Dean advantage: Ductile iron, ASTM A395 | Gray cast iron GG-25 (ASTM A278 Class 30) |
| Shaft | Dean advantage: 420 stainless (RA3146) | C45E carbon steel standard |
| Shaft sizing | Dean advantage: RA3146: 11.44 in bearing span, 1.56 in shaft between bearings | Not published |
| Made in | Dean advantage: Indianapolis, Indiana, USA | Plant not published |
Tinted rows with a check are where Dean has the advantage on published specs.
SIHI ZTN-family pumps include the ZTN, ZTK and ZTI, which Flowserve now calls the ZTND, ZTKD and ZTIC.
Send us the nameplate and duty, and we'll check whether a Dean RA fits your piping and base. SIHI uses metric PN flanges and the RA uses ANSI Class 300 (Class 150 on the RA2096), so a swap usually means adapters or spools and likely a different baseplate.
Send us your nameplate
Send a nameplate photo or the model and serial, your location, and when you need it.
888-341-7085 · sales@pumpresource.us
PumpResource is backed by Hagler Process in Chattanooga, TN. We're a Tusk Industrial Authorized Service Center for Dean, and we repair any brand of hot oil pump, including SIHI and KSB.